One Pickup Wiring Harness ~ Standard Push Pull Pot ~ Coil Split
Click To Enlarge

One Pickup Wiring Harness

Standard Push Pull Pot ~ Coil Split
One Pickup Prewired Electric Guitar Wiring Harness
Pre-Wired Harness ~ 1 Standard Push Pull Volume Control Pot
Small Pot (Dime Size) with Long Shaft
Choice of Pot & Jack Style

ITEM DESCRIPTION
These hand-wired harnesses are customized just for you and work well with most One Humbucker (or other One Pickup) Systems. Tailor your harness to your unique preferences and take your playing to new levels. We offer many style and upgrade options as well as typical replacements in standard and left-handed made-to-order wire harness versions. Each harness is unique and, based on your selections as well as current component stock on hand, may vary in appearance from the sample product images.

This harness features a DPDT push-pull small pot (dime size, approximately 16.5mm diameter x 45mm overall height) with long shaft (approximately 18mm) for body mounting. If you are going through a guard, you may need additional nuts or washers (sold separately). Audio Taper (“A” pot) or Linear Taper (“B” pot) 500K ohm styles are available (players will often use B Pots for volume and A pots for tone). Please reference our Push-Pull Standard Control Pot for additional information and measurements as needed.

The Coil Split Wiring incorporated into this harness allows you to split the coils on your humbucker in half, thus cutting one coil out and making your humbucker a single coil (also known as Coil Cut or Coil Tap). Four wire pickups are required for a coil split to work and we provide the option to choose a North Coil or South Coil style. Our provided instructions (posted in the item images, not sent as a hard copy) show the connection points from your pickup you’ll need to solder.

A Mono Jack open-frame style jack is included with each harness; this jack requires a 9mm mounting hole and tightens to your jack plate (sold separately). A Stereo Jack open-frame style jack is an optional upgrade and requires a 9mm mounting hole; this jack tightens to your jack plate (sold separately). Another option is our Barrel Jack cylinder style; this jack requires a 12mm mounting hole and tightens from inside your guitar. All Jacks work with standard cables only and accept ¼” plugs.

Soldering is required for installation; basic instructions are posted in the product images (we do not send hard copies with your order). Please know your abilities/requirements and check your measurements carefully to see if this item will work for your set-up. Before you complete your purchase, be sure to refer to the Control Pot and Jack product pages for detailed measurements and additional product information to determine if your selected options will fit for your needs (size, mounting method/requirements, style, etc.). Ask any questions before you buy.

PRODUCT HIGHLIGHTS
*Single Pickup Replacement Harness
*1 Push-Pull Standard Volume Pot
*1 Jack
*8” Insulated Wire Length (approximately)
*Lefty Option Available

WHAT’S INCLUDED (What You Get)
*1 Wiring Harness
Nothing else is included. Additional images may be provided for reference and comparison purposes only. There are no hard copy instructions or diagrams included. Basic directions are provided in the product images.

OPTIONAL ADDITIONS (Further Customize Your Harness!)
The Treble Bleed Volume Kit wiring modifier addresses the loss of high-end signal when turning down your volume pot. You’ll be able to keep more of your highs while maintaining volume adjustability. This wiring option allows a more constant tone throughout the range of your volume pot and helps remove the dark muddiness typically experienced in the lower volume pot settings.

The Kill Switch Wiring Option allows you to kill the signal to the amp using an on-off, two-way SPST toggle mini-switch. The shaft diameter is roughly 5.85mm so you’ll need a 6mm hole (1/4” bit).

PURCHASE NOTES (Read Before Buying)
Buyers assume all risk of use; sales are only offered to those competent to safely and lawfully purchase and use items.
ASK ANY QUESTIONS PRIOR TO PURCHASE. Due to the vast and varied nature of possible set-ups, we do not provide specific information for every possible installation scenario. The provided BASIC instructions (posted in the item images, not sent as a hard copy with your order) will get you started. Depending on your set-up, you may require adjustment – please ask any questions before you buy if the posted instructions are not sufficient for your install or if you are unsure of your needs or ability to make modifications (if needed) for your unique situation.
Inspect your order upon receipt. We will address any issues PRIOR to installation.

  • Item #: 1006

1V One Pickup Wiring Harness ~ Standard PUSH PULL ~ COIL SPLIT

Price: $12.95
* Marked fields are required.
Qty: *
Reviews (0) Write a Review
No Reviews. Write a Review